Peer reviewed Publikation in Master Journal Liste (Clarivate)
Refine
Year of publication
- 2020 (4)
Document Type
- Article (4)
Language
- English (4)
Has Fulltext
- no (4)
Additive manufacturing offers unique possibilities to produce complex components, which would not be possible or only very difficult to be realizable with conventional manufacturing processes. The potential of additive manufacturing of aluminum alloys has already been realized in prototyping, but still offers potential in the establishment of series applications. For enabling the establishment of additive manufacturing in series applications, comprehensive knowledge about the material behavior is necessary. This study examines the torsional behavior of additive manufactured AlSi10Mg samples and shows the correlation between tensile and torsional strength. Comprehensive torsion tests with strain gauges were performed and significant directional dependencies were shown. The correlation factor in the area of torsional yield strength/tensile yield strength and torsional strength/tensile strength was determined and was compared with the yield/failure conditions according to Tresca and von Mises.
Metal additive manufacturing of dental prostheses consisting of cobalt−chromium−tungsten (Co−Cr−W) alloys poses an alternative to investment casting. However, metal additive manufacturing processes like Laser Powder‐Bed Fusion (LPBF) can impact the elastic constants and the mechanical anisotropy of the resulting material. To investigate the phase compositions of mechanically different specimens in dependence of their postprocessing steps (e. g. heat treatment to relieve stress), the current study uses X‐ray Diffraction (XRD), Electron BackScatter Diffraction (EBSD), and Transmission Electron Microscopy (TEM) for phase identification. Our studies connect plastic deformation of Remanium star CL alloy with the formation of the hexagonal ϵ‐phase and heat treatment with the formation of the D024‐phase, while partially explaining previously observed differences in Young's moduli.
Das Interesse der Industrie an additiv gefertigten Bauteilen steigt z unehmend, wobei mit zunehmendem Verständnis der statischen Kennwerte nunmehr der Fokus in Richtung der dynamischen Festigkeiten wandert. Deswegen werden Einflussparameter auf die Lebensdauer und potenzielle Nachbearbeitungsmethoden untersucht und analysiert. Ein großer Einfluss ist dabei der Oberflächengüte und den durch Rautiefen initiierten Kerbeffekten zuzuschreiben. Deswegen werden unterschiedliche Methoden zur Verbesserung der Oberflächengüte untersucht. Dabei werden die Verfahren Laserpolieren, elektrochemisches Polieren und Hartmetallkugelstrahlen und deren Auswirkung auf Oberflächengüte sowie Härte untersucht. Für das elektrochemische Polieren werden die Proben in einer Perchlorsäure für 90 s bei 32 V und maximal 10 A poliert. Das Hartmetallkugelstrahlen wird mit einem UFS 100 Strahlmittel bei einem Druck von 4 bar und einer Strahldauer von 10 s ausgeführt. Anschließend werden Wöhlerlinien für die unterschiedlichen Zustände mittels Umlaufbiegeversuch ermittelt, welche mit Referenzwerten analysierter konventioneller Proben verglichen werden. Des Weiteren werden die Bruchflächen analysiert. Die Untersuchungen ergaben ein hohes Optimierungspotenzial der additiv gefertigten Proben bei einer Verdichtung der Oberfläche sowie einer Entfernung der Randschicht durch eine spanende Bearbeitung. Dadurch wurden höhere Zeitfestigkeiten als mit konventionell gefertigten Proben erreicht.
Laser powder-bed fusion (LPBF) has significantly gained in importance and has become one of the major fabrication techniques within metal additive manufacturing. The fast cooling rates achieved in LPBF due to a relatively small melt pool on a much larger component or substrate, acting as heat sink, result in fine-grained microstructures and high oversaturation of alloying elements in the α-aluminum. Al-Si-Mg alloys thus can be effectively precipitation hardened. Moreover, the solidified material undergoes an intrinsic heat treatment, whilst the layers above are irradiated and the elevated temperature in the built chamber starts the clustering process of alloying elements directly after a scan track is fabricated. These silicon-magnesium clusters were observed with atom probe tomography in as-built samples. Similar beneficial clustering behavior at higher temperatures is known from the direct-aging approach in cast samples, whereby the artificial aging is performed immediately after solution annealing and quenching. Transferring this approach to LPBF samples as a possible post-heat treatment revealed that even after direct aging, the outstanding hardness of the as-built condition could, at best, be met, but for most instances it was significantly lower. Our investigations showed that LPBF Al-Si-Mg exhibited a high dependency on the quenching rate, which is significantly more pronounced than in cast reference samples, requiring two to three times higher quenching rate after solution annealing to yield similar hardness results. This suggests that due to the finer microstructure and the shorter diffusion path in Al-Si-Mg fabricated by LPBF, it is more challenging to achieve a metastable oversaturation necessary for precipitation hardening. This may be especially problematic in larger components.